Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

某机载探测系统自主回收技术的实现

针对某机载探测系统探头回收自动化程度低的问题，提出了在无需操作员干预情况下实现探头自主回收的技术方法。采用了先进的控制算法，将缆位角与探头、缆长进行结合并引入了绞车控制系统，使绞车对探头的回收速度及缆长可进行实时调整，并给出了3种不同缆位角摆动条件下缆长与探头回收速度的控制曲线关系。研发了自主回收装置，设计了能够实现自主回收功能的探头回收机构。实验验证表明：在无需人为干预的条件下，在缆位控制系统及自主回收机构的配合下，系统实现了对探头快速、安全的回收。     

基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法

半球谐振子频率裂解与固有刚度轴方位角是影响陀螺性能指标的核心因素。提出了一种基于幅频响应特性的半球谐振子频率裂解与固有刚度轴方位角测定方法，采用压电激振台扫频激振，多普勒激光测振仪检测谐振子的幅频响应特性，通过幅频响应特性曲线分析实现频率裂解与固有刚度轴方位角的测定。对该方法进行了理论分析，搭建了实验装置，并对半球谐振子进行了测试，结果表明：该方法频率裂解测量精度优于0.01Hz，固有频率主轴方位角确定精度优于±1.17°，具有良好的可行性，在半球谐振陀螺研制方面具有良好的参考意义。     

H5飞机调油方法研究

对Ｈ５飞机经过了计算、论证、试飞，在此基础上提出了一种既安全又能充分发挥飞机飞行性能，同时又使动作程序化的调油方法－－规划调油法。用这种调油就可以大大地减少飞行员操纵飞机进的注意力分散，更利于集中精力操纵飞机，以保证飞行的安全。     

利用热源温度场迭加法诊断持续点热源的强度及位置

可重复使用运载器的防热瓦故障会使航天器的局部结构产牛热源，并在结构中形成温度场。应用热源温度场迭加法的解函数，解得结构温度历程，然后据此温度的变化率趋势判断出热源位置，在此基础上依据多点测最值构造出辨识参数用于热强度识别，通过对一薄壁结构模型算例的计算仿真，证明了本文所提方法的有效性。论文工作为进一步开展热源诊断技术研究，提供了可资工程实践应用的数值算法体系以及有益的数值计算结论。     

拉格朗日中值定理的一个新证法

本文给出了利用坐标旋转法证明拉格朗日中值定理的一种新方法。即从罗尔定理出发，采用坐标旋转法及隐函数、复合函数求导法则，证明拉格朗日中值定理，由于该证明方法从直观的几何意义入手，因此，其证明过程更加清晰、易懂。     

钣金制件表面的相贯线求作方法

本文提出钣金制件表面相贯线求作的新方法。     

Investigation of the differential rotation of the large-scale magnetic elements for the solar activity cycles 20 and 21

The differential rotation of the patterns of the large-scale solar magnetic field during solar activity cycles 20 and 21 is investigated. Compact magnetic elements with the polarity of the general solar magnetic field have larger speed of rotation than the elements with the opposite polarity. The surface of the Sun was divided by 10°-zones. In all of them the average rotation rate of the magnetic elements with negative polarity is little higher than that of the magnetic elements with positive polarity, except for 50°-zone of the south hemisphere and at the 10° latitude of the north hemisphere.

The rates of differential rotation for large-scale magnetic elements with negative and positive polarities have similar behavior for both cycles of the solar activity.

The rotation rate varies at polarity reversal of the circumpolar magnetic fields. For the cycle No 20 in 1969–1970 the threefold reversal took place in the northern hemisphere and variations of rotation rate can be noticed for magnetic elements both with positive and negative polarity for each 10°-zone in the same hemisphere.     

FY—1C卫星姿态控制系统

针对FY－1C卫星姿态控制系统，给出了系统方案、系统设计、系统特点和飞行试验的结果；对一些新的技术设计和新颖特殊的方案特点，从理论分析和技术实现给出了设计思路和工程实现的方法；分析了FY－1C卫星姿态控制系统在轨运行的结果；对长寿命、低成本和稳定连续运行的工程实现进行了研究；给出了FY－1C卫星姿态控制系统的水平能力和应用发展方向。     

全位置自动焊管机TIG焊电源研制

本文介绍了一种适用于管－管、管－板对接的全位置自动TIG焊晶体管电源，该电源采用可编程控制器控制，具有直流／脉冲功能，焊接参数在4个区间内可分别预测，试验表明，该电源区间过渡时电弧稳定，抗干扰能力强，焊缝均匀、连接。